What To Do If Kitchenaid Refrigerator Light Not Working?

Wondering what to do when the KitchenAid refrigerator light not working? The KitchenAid fridge is a favorite kitchen appliance in most modern homes. It is good to have this fridge in the house since it will save you time and money as well.

There are many things that can go wrong with your KitchenAid fridges, such as broken lights or compressor issues. Luckily, there are some steps you can take to troubleshoot these issues and get your fridge working again.

Below are a few tips for troubleshooting light issues in the KitchenAid fridge.

KitchenAid Fridge Lights Not Working

1. The door is open for longer than 10 mins

If you leave the door open for longer than 10 minutes, then the light will turn off automatically. This is to prevent any unnecessary energy consumption and overheating of the radiator or compressor. So, make sure that your fridge is closed when you are not using it.

2. There’s a faulty sensor or wiring issue

The light in your fridge is controlled by a sensor. If this sensor is not working properly, then the light will not turn on. You can check the sensor by opening up the fridge and locating it near the door hinge. If the sensor is damaged or loose, then you will need to replace it.

See also  Pex Fridge Water Line

3. The bulb is burned out

If the fridge light is still not working after you try the above tips, then it may be because the bulb has burned out. You can replace the LED or fluorescent bulbs in your KitchenAid fridge by following the instructions in your owner’s manual.


4. Light switch not activating

First, check to see if the switch is in the “on” position. If it is, then the issue maybe with the wiring. You can check this by opening up the fridge and locating the light switch. Once you find the switch, you can use a multimeter to test the continuity of the wires. If there is no continuity, then you will need to replace the wires.

5. Replace the wiring harness

If the wires are working properly, then there may be a problem with the wiring harness. You can check for this by removing the light socket and testing it with a multimeter. If you find any issues with the socket, then you will need to replace it.

6. The refrigerator is not plugged in or has a disconnected power supply

If your KitchenAid fridge is still not working after checking all of these things, then there may be a problem with the power supply. Make sure that your fridge is plugged in and that there are no tripped fuses or blown circuit breakers.

7. Sabbath mode on Sabbath day

Sabbath Mode is a setting that disables the fridge light on Sabbath day. This is to comply with the Jewish religious law. To turn off Sabbath mode, you will need to press and hold the power button for 3 seconds.

See also  Ice Maker Smells Like Garlic?

8. Firmly close the door

If your fridge light is still not working, then make sure that the door is firmly closed. If the light does not turn on, then there may be a problem with the seal and gasket. You can check this by removing the gasket from the fridge and checking for any dirt or food particles that may be obstructing it.

If needed, you can clean out the gasket and replace it to get your fridge working again.

How do you remove the light shield on a KitchenAid refrigerator?

To remove the light shield on a KitchenAid refrigerator at home, first, locate the two screws that hold it in place. Once you have found the screws, use a screwdriver to remove them. After the screws are removed, the light shield should come off easily.

If not, then you may need to use a putty knife to pry it off. Once the shield is off, you can use a multimeter to test for any loose wires or damaged components.

If you find any problems with the wires or components, then you will need to replace them. Otherwise, simply reattach the light shield and your fridge should be working again.

Is there a way to reset a KitchenAid refrigerator?

Yes, there is a way to reset a KitchenAid refrigerator. To do this, first, unplug the fridge from the power outlet. Next, locate the reset button on the control panel. Once you have found the reset button, press and hold it for 3 seconds.

After 3 seconds, the fridge should be reset and all of the lights should be turned off. If the fridge does not reset, then you may need to press and hold the button for longer.

See also  How To Do A Oven Kitchenaid Over Temperature Reset

How do I install a KitchenAid refrigerator light switch?

To install a refrigerator light switch, start by removing the cover plate that is covering the switch. Once the cover plate is off, use your multimeter to test for continuity across the wires leading to the switch.

If the continuity is good and your fridge light continues to not work, then the problem may be with the switch itself. You can replace it by disconnecting the wires from behind the switch and removing it from the wall.

Next, connect new wires to your fridge unit and attach a new switch. Finally, test your refrigerator light to make sure that it is working properly.

If all of these steps are completed successfully, then you should have a fully functioning refrigerator light switch.

How do I know if my KitchenAid refrigerator light bulb is bad?

If your KitchenAid refrigerator LED light is not working, then you can test it with a multimeter. To do this, remove the light socket from the fridge and set it to the ohm setting on your multimeter.

Touch one lead of the multimeter to one of the metal prongs inside of the socket and touch the other lead to the glass portion of the bulb. If there is no continuity, then you should replace your light bulb. Otherwise, continue troubleshooting to find out what may be causing your fridge light to not work properly.

Final Verdict – What To Do If Kitchenaid Refrigerator Light Not Working

So, this guide has answered all your questions regarding What To Do If Kitchenaid Refrigerator Light Not Working. Follow our blog to read posts like this.

 

Today's Deals